Audi A4

since 1994 of release

Repair and car operation



A4 Audi
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ exhaust System
+ cooling System
+ Fuel tank and fuel pump
+ Air filter and absorption channels
+ injection System
+ Coupling
+ Transmission and main transfer
- Suspension bracket of wheels and steering
   Running gear
   Check of cuffs of the steering mechanism
   Check of dustproof caps and gap in heads of cross-section steering draft
   Check of dustproof caps of hinges of an axis
   Check люфта steering wheel
   Check of a maple belt
   Check of level of oil
   Check of a gap of the wheel bearing
   Shock-absorbers
   Check of shock-absorbers
   The help at malfunctions
   Adjustment of wheels
   Measurement of adjustment of wheels
   The help at malfunctions
   Independent works on a running gear and a steering
   Dismantling of a suspension bracket of forward wheels
   Works with the back bridge
   Shock-absorber replacement behind
   Steering
   Works on a steering
   Check of tightness of a servoupravleniye
   Poliklinova belt
   The help at malfunctions
   Adjustment of the steering mechanism
   Dismantle of the pump of a servoupravleniye
   Filling and pumping of system of a servoupravleniye
   Safety cushion
   Safety instructions
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ ignition System
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
+ body Details
+ Salon
Search of malfunctions
Technical characteristics





Works on a steering

External end of cross-section steering draft

1–an adjusting bolt of a convergence of wheels on turn;
2–tightening bolt of cross-section steering draft;
3–head of cross-section steering draft;

4–lock-nut;
5–shestigrannik of cross-section steering draft.


The arrow indicates the assembly provision of an adjusting bolt of the steering mechanism.

Replacement of a head of cross-section steering draft

 PERFORMANCE ORDER

  1. Remove a wheel.
  2. Unscrew самоконтрящуюся a nut on a tightening bolt of cross-section steering draft.
  3. Take out tightening a bolt.
  4. Unscrew an adjusting bolt of a convergence of wheels on turn.
  5. Squeeze out a head of cross-section steering draft down from a wheel soshka on the case of the wheel bearing.
  6. Unscrew a lock-nut on a head of cross-section steering draft, wring out thus a shestigrannik of cross-section steering draft in an opposite direction.
  7. Designate the provision of screw connection of cross-section steering draft, then after a svinchivaniye the width of a track will be approximately the same.
  8. Unscrew a head of cross-section steering draft, transfer marking on a new head of steering draft.
  9. Installation: press a finger of a head of cross-section steering draft into a wheel soshka if it is necessary, carefully hammer.
  10. Tighten new самоконтрящуюся a nut on 40 Nanometers.
  11. Tighten also on 40 Nanometers of a lock-nut.
  12. Check a convergence of wheels.

Replacement of cross-section steering draft assembled

This work sometimes is not possible because of inaccessibility of screw connection between cross-section steering draft and the steering mechanism. For this screw connection there is V.A.G 1923 key, allowing to tighten this screw connection on 100 Nanometers. It is recommended for application.

 PERFORMANCE ORDER

  1. Separate a head of cross-section steering draft from a steering soshka how it is described in the previous section.
  2. Weaken сильфон on cross-section steering draft and the steering mechanism, remove.
  3. Unscrew cross-section steering draft from a lead of the steering mechanism.
  4. Installation: grease the internal hinge with greasing for the steering AOF 063 000 04 mechanism.
  5. Screw up new cross-section steering drafts on a lead of the steering mechanism on 100 Nanometers.
  6. Establish сильфон.
  7. Fix a head on cross-section steering draft and a wheel soshka how it is described above.
  8. Check a convergence of wheels.