Audi A4

since 1994 of release

Repair and car operation



A4 Audi
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ exhaust System
+ cooling System
+ Fuel tank and fuel pump
+ Air filter and absorption channels
+ injection System
+ Coupling
+ Transmission and main transfer
+ Suspension bracket of wheels and steering
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ ignition System
- Lighting
   Lighting check
   Spare lamps
   Replacement of lamps of headlights
   Headlight dismantle
   Check of adjustment of headlights
   Fog lights
   Lamps of forward indexes of turns
   Back lamps
   Lamps of illumination of registration plate
   Lamp of illumination of salon
   Lamps for illumination of a control panel
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
+ body Details
+ Salon
Search of malfunctions
Technical characteristics





Lamps for illumination of a control panel

Illumination of devices

In this section it is a question of illumination of display devices. The description of the control bulbs which have been also located in the combined device, you will find Tools and devices in head. Dismantle of illumination of devices:

 PERFORMANCE ORDER

  1. Dismantle a steering wheel (head the Suspension bracket of wheels and a steering).
  2. Dismantle the combined device (head Tools and devices).
  3. Behind the combined device depending on model about nine cartridges of bulbs for illumination of devices are visible.
  4. For replacement turn them to the left and take out.
  5. Bulbs with a glass socle on 1,1 W form one constructive element with the boss.
  6. Again insert into the combined device a cartridge with a lamp and turn to the right against the stop.
  7. In cars with the board computer for illumination of the display five bulbs with glass socles on 1,1 W are used.
  8. Some bulbs for illumination of devices – depending on the manufacturer – are supplied with orange protective caps. It is possible to establish caps on new filament lamps.

At the left: lateral illumination of a luggage carrier to identically top illumination of a luggage carrier. The arrow showed an assembly opening for the case of a lamp (1); figure «2» designated the filament lamp.

On the right: for illumination of a regulator of heating the small bulb (1) serves. Through one light guide (2; here will take out from clips) lighting is distributed on all three scales of handles of control.


For illumination of knot of manual control by climatic installation four small bulbs are used. The boss and a bulb form one constructive element which it is possible to replace by means of a screw-driver (turn on a turn quarter to the left).


Box lamp for gloves: carefully wring out a screw-driver the case (2) bulbs from an assembly opening. After that there is available a sofitny filament lamp (1).


Dismantle of the case of the ashtray/lighter: open an ashtray (2), a screw-driver (1) take out from spring grooves in both dredging (arrow) and extend the case back.


Here the bulb of illumination of the ashtray/lighter (2) is removed from the lighter (1) at the case of an ashtray dismantled and turned by a reverse side.

Illumination of the lever of heating

 PERFORMANCE ORDER

  1. Dismantle a radio receiver (head Tools and devices).
  2. Weaken in an assembly opening of a radio receiver four screws.
  3. Remove the decorative panel of the average console (switches remain on a place).
  4. Pull back all three rotary regulators of heating/ventilation.
  5. Unscrew under them two screws with crosswise heads, remove the decorative panel.
  6. Take out from clips a light guide.
  7. Now the bulbs inserted here with glass socles on 1,2 W are visible.
  8. Bulbs can be taken out on one from the boss.

Illumination of knot of manual control by climatic installation

 PERFORMANCE ORDER

  1. Take out from clips a radio receiver (head Tools and devices).
  2. Weaken in an assembly opening of a radio receiver four screws.
  3. Remove the decorative panel of the average console (switches remain on a place).
  4. Unscrew four fixing screws of knot of manual control by climatic installation and take out knot.
  5. On a reverse side turn to the left cartridges of lamps and take out them.
  6. Bulbs with glass socles on 2 W form one constructive element with the boss.
  7. Both average bulbs at both external – have no black border.

Illumination of the ashtray/lighter ahead

 PERFORMANCE ORDER

  1. Open an ashtray (2) in the average console.
  2. Insert a screw-driver into one of two dredging behind an ashtray and wring out down on the basis of the ashtray case a fixing spring.
  3. It is easier for making if to shine with a manual small lamp in dredging.
  4. Repeat the same process with the second spring.
  5. Take out back an ashtray together with the case.
  6. Raise a small fixing slip, take out a cartridge of a lamp on the lighter.
  7. Replace a lamp.

Lamp for illumination of a box for gloves

Tension on a bulb for illumination of a box for gloves arrives at the included lay or dimensional lamps. It joins and switched off by the contact switch in the hinge.

 PERFORMANCE ORDER

  1. Open a box for gloves.
  2. Insert a screw-driver into dredging sideways on the case of a lamp and carefully wring out a lamp.
  3. After filament lamp replacement (a sofitny bulb of 5 W, length of 36 mm) again insert the lamp case, in the beginning that party, where a wire.

Transfer indicator

For illumination of the indicator of transfer on the lever selector of an automatic transmission the lamp with a glass socle (1,2 W, a form W on DYNES standard) serves.

 PERFORMANCE ORDER

  1. Dismantle the average console (head Salon).
  2. Take out from clips a cartridge of a lamp at the left on the lever selector console.
  3. Take out a lamp with a glass socle from the boss.

Bulbs in switches

Almost in all switches there are shined symbols, but this lighting is not intended for replacement. Therefore in case of defect it is necessary to consider the dark switch or to replace it.